[Apr 11, 2025] Pass Senior-Internal-Corrosion-Technologist Review Guide, Reliable Senior-Internal-Corrosion-Technologist Test Engine
Senior-Internal-Corrosion-Technologist Test Engine Practice Test Questions, Exam Dumps
NEW QUESTION # 35
The coating applicator has ignored a surface preparation hold point and applied coating over the surface without a sign off from you as the inspector.
Your FIRST preferred course of action is to:
- A. Require the Applicator to remove the applied coating
- B. Stop the Job
- C. Advise the Owner and write a Non-Conformance report
- D. Ignore the situation
Answer: C
NEW QUESTION # 36
The number of air turns in an enclosure can be affected by all of these EXCEPT
- A. time of the year (winter/summer).
- B. manufacturer of the equipment.
- C. coating type.
- D. type of dehumidification equipment (refrigerant or desiccant).
Answer: D
NEW QUESTION # 37
When performing a hardness test on a coating which has elastic properties the inspector is likely to observe:
- A. A very high reading
- B. Cold (low or creep
- C. No difference from any other coating
- D. A very low reading
Answer: B
NEW QUESTION # 38
A failure caused by applying a coating too thinly is known as
- A. chalking.
- B. cracking.
- C. pinholes.
- D. failure to cure.
Answer: C
NEW QUESTION # 39
The cost of qualified Coating Inspection Is normally offset by:
- A. Lower Supervision Costs
- B. Lower Application Costs
- C. Lower Safety Enforcement Costs
- D. Lower Coating Life Cycle Costs
Answer: D
NEW QUESTION # 40
Which type of pipelines collect the gas from the transmission system so utility companies can distribute the gas to end users?
- A. Midstream
- B. Gathering
- C. Transmission
- D. Distribution
Answer: A
NEW QUESTION # 41
Antifouling coatings are regulated by international treaties.
- A. True
- B. False
Answer: A
NEW QUESTION # 42
Differences in technique for abrasive blasting concrete versus steel require the operator to:
- A. Lower the blast pressure
- B. Move the nozzle quicker
- C. Increase the standoff distance
- D. a), b) and c)
Answer: D
NEW QUESTION # 43
When working with someone who Is very concerned about stability and maintaining adherence to the status- quo, the Inspector should try to:
- A. Make sure they are the center of attention in all site meetings
- B. Implement Immediate changes to get them motivated
- C. Give them as much advance notice as possible about upcoming changes
- D. Challenge their value to the team and try to get them out of their comfort zone
Answer: C
NEW QUESTION # 44
When using a destructive Paint Inspection Gauge the NACE inspector must:
- A. Consult SSPC Guide 1 prior to use
- B. Select the appropriate hand wheel based on the measured Dry Film Thickness prior to use
- C. Ensure the glue on the dolly is properly applied prior to use
- D. Determine the Dry Film Thickness of the coating prior to use
Answer: B
NEW QUESTION # 45
NACE International Standards are developed by:
- A. Government mandates
- B. Regional mandates
- C. International mandates
- D. Standard committees
Answer: B
NEW QUESTION # 46
Application of Thermal Spray Coatings requires:
- A. No particular skills
- B. Specialized skills supported by training and experience
- C. The same skills as liquid coatings
- D. The same skills as welding
Answer: B
NEW QUESTION # 47
Pre-cleaning of work pieces will NOT remove
- A. dirt.
- B. oil or grease.
- C. snow, ice or water.
- D. mill scale.
Answer: D
NEW QUESTION # 48
As a NACE Level 2 Inspector on a field Job; prior to submission your documentation should always be reviewed and approved by:
- A. A NACE Protective Coating Specialist
- B. Another NACE Level 2 Inspector
- C. A NACE Level 3 Inspector
- D. A NACE Level 1 Inspector
Answer: C
NEW QUESTION # 49
You are working as an Inspector in a galvanizing plant for the first time. What are some of the hazards you need to be aware of:
- A. Risk of skin burns
- B. a), b), and c)
- C. Risk of acid or caustic splashes
- D. Risk of chemical exposure
Answer: B
NEW QUESTION # 50
When environmental enclosures ate being used an inspector needs to be concerned about:
- A. Structural integrity
- B. a), b), and c)
- C. Air changes
- D. Lighting
Answer: B
NEW QUESTION # 51
You are the NACE Level 2 Inspector with the final responsibility to prepare the final report for a very large structural steel shop project which has gone very well. It Is due next week. The work has been ongoing for two years and several NACE Level 1 Inspectors have worked under your supervision throughout the project.
You find you are missing one week of daily reports for the night shift from the very beginning of the project and despite your best efforts they are cannot be found.
You FIRST preferred course of action Is to:
- A. EXInot complete your report until they can be found
- B. Use creative writing to cover over the fact they are missing
- C. Re-create the reports as not much was going on during night shift anyway
- D. Plainly state in your report that they are missing
Answer: D
NEW QUESTION # 52
Which surface preparation method uses a dilute add solution to remove laitance and roughen the concrete surface?
- A. Add etching
- B. Sacking
- C. High-pressure water washing
- D. Stoning
Answer: A
NEW QUESTION # 53
Linings are used on the interior of pipelines to
- A. afford limited temperature Insulation.
- B. protect the transported product.
- C. reduce magnetic polarity.
- D. provide protection against soil chemicals.
Answer: B
NEW QUESTION # 54
When observing fabrication defects the NACE Inspector should:
- A. Require they be corrected prior to coating
- B. Write an NCR and call the fabricator
- C. Stop the job immediately
- D. Consult the specification to determine how they should be treated
Answer: D
NEW QUESTION # 55
You are a NACE Level 2 in-house inspector working in a shop. Your In-house UP requires you to perform a sleeve test to test for soluble sails; however the 3rd party NACE Level 3 inspector, representing the owner, has used a salt smart meter and has achieved a very different result and has rejected the pre cleaning.
Your FIRST preferred course of action is to:
- A. Redo the pre-cleaning based on the other Inspectors results
- B. Advise your QC Manager to change the UP to the use of the salt smart meter
- C. Advise the other Inspector he is using an Incorrect method
- D. Review the specification with the other inspector to see what method was specified
Answer: D
NEW QUESTION # 56
Which is used to calibrate a pH meter?
- A. standard buffer solution
- B. Deionized water
- C. Distilled water
- D. Standard solvent solution
Answer: A
NEW QUESTION # 57
NACE No. 13/ SSPC 6 Identifies the use of:
- A. Steam cleaning only
- B. Various methods of cleaning
- C. Watterjetting only
- D. Abrasive blasting only
Answer: B
NEW QUESTION # 58
......
100% Free Senior-Internal-Corrosion-Technologist Daily Practice Exam With 102 Questions: https://passguide.validtorrent.com/Senior-Internal-Corrosion-Technologist-valid-exam-torrent.html